[fredbear]

What would my measurements be on the right antler? I may be wrong but I am thinking that I would get a mass measurement between the G2 on the small point and then between the small point and 'G3'.....or would that considered a non-typical point and just get one measurement between the G2 and 'G3'.....or would the small point be considered the G3.......The more I type the more confused I get.

http://i208.photobucket.com/albums/bb56/fredbear_10/3-2-08056.jpg

 

[odocoi]

it looks to me like it originates from the mainbeam and grows upward like a typical point so it should be your G3 IMO

 

[fullcredit]

From the pic, it looks like a typical point to me, so consider it the G3. Some may not realise (yes, I know there isn't an "s" in that word, but the correct key for that word doesn't work!) it, but even on a four point side like the left side in the pic, you still get four circumference measurements.

 

[Mr. Chitlin]

That will be some big time deductions on the B&C system!!

 

[born2hunt]

It looks like a non-typical point to me.

 

[10pointman]

Boone and Crockett.com

 

[fredbear]

..... but even on a four point side like the left side in the pic, you still get four circumference measurements.

I did not know that but here it is.

If G-4 is missing, take H-4 halfway between the center of G-3 and tip of main beam. (Pope and Young).

 

[fullcredit]

You got it!:thumb: Eight circumference measurements on all deer.

 

[fredbear]

it looks to me like it originates from the mainbeam and grows upward like a typical point so it should be your G3 IMO

So would the point just above the browtine be counted as a typical point too...it comes off the top of the main beam and then goes back. I am not tring to be a smart A, I am just trying to figure out how I would score this rack. I didn't kill it so it doesn't matter to me what it scores, I am just tring to expand my knowledge. :biggrin:

Here is another pic that shows the point I am talking about a little better.
http://i208.photobucket.com/albums/bb56/fredbear_10/3-2-08049.jpg

 

[odocoi]

i don't really know. My guess would be that since it's in a spot on the mainbeam where there isn't usually an additional point that in may be considered non-typical.

 

[RPatton86]

Score

That Is A Non-typical Point

 

[CP]

Actually it is classed as an Abnormal Point.

Item "E" from scoresheet....


E. Total of Lengths of all Abnormal Points:

Abnormal Points are those non‑typical in location (such as points originating from a point or from bottom or sides of main beam) or extra points beyond the normal pattern of points. Measure in usual manner and enter in appropriate blanks.

Total of both tines would be a "deduction".​

 

[odocoi]

Actually it is classed as an Abnormal Point.

Item "E" from scoresheet....


E. Total of Lengths of all Abnormal Points:

Abnormal Points are those non‑typical in location (such as points originating from a point or from bottom or sides of main beam) or extra points beyond the normal pattern of points. Measure in usual manner and enter in appropriate blanks.

Total of both tines would be a "deduction".​

the point on out on the mainbeam is consistent with the normal pattern of points isn't it?​

 

[Savage Shooter]

Actually it is classed as an Abnormal Point.

Item "E" from scoresheet....


E. Total of Lengths of all Abnormal Points:

Abnormal Points are those non‑typical in location (such as points originating from a point or from bottom or sides of main beam) or extra points beyond the normal pattern of points. Measure in usual manner and enter in appropriate blanks.

Total of both tines would be a "deduction".​

This is correct!!:smack:​

 

[CP]

the point on out on the mainbeam is consistent with the normal pattern of points isn't it?

No they both are not pattern consistant...:wink:

 

[odocoi]

No they both are not pattern consistant...:wink:

explain that please

 

[Savage Shooter]

explain that please

This rack has normal G1's and normal G2's and normal G'3s so the additional point above the G1 is abnormal to pattern.

Also the little point between the G2 and G3 does not fit "normal/typical" pattern so it is abnormal also. They are both deductions scored typical.

The little point between the G2 and G3 does not matter what direction it grows off the main beam. Up, down, or a sticker out to the side, it is still a deduction because it is not of normal length or "fit" the pattern of the rest of G's.

This is a typical 8 pt frame with 2 abnormal points that are deductions, period.

 

[CP]

explain that please

A two inch long tine halfway between a normal spaced 10" long G2 and a 9" long G3 on a mainframe eight is not considered a "normal" occurrence....therefore it is an abnormal tine. It coming up from the mainbeam is not a consideration in this case...size and location is the determining factor.

The tine next to the G1 on the right antler is for sure an abnormal occurrence...(same as a double eye guard would be....double eye guard is not listed as a G1 and a G2..would be a G1 and an abnormal tine)

 

[CP]

This rack has normal G1's and normal G2's and normal G'3s so the additional point above the G1 is abnormal to pattern.

Also the little point between the G2 and G3 does not fit "normal/typical" pattern so it is abnormal also. They are both deductions scored typical.

The little point between the G2 and G3 does not matter what direction it grows off the main beam. Up, down, or a sticker out to the side, it is still a deduction because it is not of normal length or "fit" the pattern of the rest of G's.

This is a typical 8 pt frame with 2 abnormal points that are deductions, period.

Exactly....:up:

 

[odocoi]

you'll have to humor me here but what if the G 2 on the right mainbeam had been broke off in a fight and was only 2 in. long. Would it then be considered a non-typical point?